Zanussi Z816WT85BI User Manual

GETTING STARTED?EASY.User ManualZ816WT85BIEN User ManualWasher Dryer

5. Connect the water inlet hose to the cold water tapwith 3/4 thread.WARNING! Make sure that there are noleaks from the couplings.Use the hose supplie

LTo a wall-pipeDirectly to a built-in drain pipe in the room wall andtighten it with the supplied cable tie L.You can extend the drain hose to maximum

Before proceeding with appliance building in, bring itnear the recess and preposition the inlet hose, thedrain hose and the mains cable.WARNING! Make

Factory pre settingThe appliance is originally pre set for the assembly ofa cupboard door opening from right to left.The best solution would be to scr

xyyCupboard door preparationFor countersinking the door, it is recom-mended to call a professional.Align the cupboard door to the furniture correctly.

Mounting the doorFix the hinges to the hinge supports on the appli-ance by means of the two supplied screws B.The hinges can be adjusted to compen-sat

7Plate with rubber beater8Drain pump filter9Front feet for levelling the appliance10Drain hose11Mains cable12Inlet hose connection13Back feet for leve

DISPLAYDoor locked indicator.The digital indicator can show:• Programme duration (e. g. , washing and/or drying phase).• Delay time (e. g. ).• Cycle

DIAL AND BUTTONSINTRODUCTIONThe options/functions are not availablewith all washing programmes. Checkthe compatibility between options/functions and w

FLEXTIME With this option you can reduce the programmeduration depending on the load size and the degreeof soiling.When you set a washing programme, t

SAFETY INFORMATIONBefore the installation and use of the appliance, carefully read thesupplied instructions. The manufacturer is not responsible for

PROGRAMMESPROGRAMME CHARTProgrammeDefault temperatureTemperature rangeReferencespin speedSpin speedrangeMaxi-mumloadProgramme description(Type of load

ProgrammeDefault temperatureTemperature rangeReferencespin speedSpin speedrangeMaxi-mumloadProgramme description(Type of load and soil level)Machine C

ProgrammeDefault temperatureTemperature rangeReferencespin speedSpin speedrangeMaxi-mumloadProgramme description(Type of load and soil level)NonStop 6

Programme Spin No Spin Prewash Flextime Delay StartMachine Clean Daily Wash Sportswear Outdoor Denim

Dryness Level Type of fabric Load1)Cupboard Dry2)For items to be storedCottons and Linen(bathrobes, bath towels, etc)up to 4 kgSynthetics and mixed fa

Dryness Level Type of fabricLoad(kg)Spinspeed(rpm)Suggested du-ration (mins)Cupboard DryFor items to bestoredCottons and Linen(bathrobes, bath towels,

3. Pour a small quantity of detergent into thecompartment marked by .4. Set and start a programme for cotton at thehighest temperature without any la

2. Press the lever down to remove the dispenser.3. To use powder detergent, turn the flap up.4. To use liquid detergent, turn the flap down.With the f

Changing the delay start after the countdownhas startedTo change the delay start:1. Touch the Start/Pause button to pause theappliance. The related

END OF THE PROGRAMMEWhen the programme has finished, the appliancestops automatically. The acoustic signals operate (ifthey are active). The display s

– by clients in hotels, motels, bed & breakfast and otherresidential type environments;– areas for communal use in blocks of flats or in launderet

2. Set the NonStop 60min programme by meansof the programme dial.3. Touch the Start/Pause button to start theprogramme.Non-automatic wash&dry pr

PREPARATION TO DRYING1. Press the On/Off button for some seconds toactivate the appliance.2. Load the laundry one item at a time.3. Turn the programme

• Clean the drum, the gasket and the door with awet cloth.• Set the Machine Clean programme and theMode - Dry together to activate the anti-fluffactio

PREPARE THE DRYING CYCLE• Open the water tap.• Check if the drain hose is connected properly.Refer to installation chapter for moreinformation.• For t

drum and the tub. This could generate bad odoursand mildew. To eliminate these deposits and cleanthe inner part of the appliance, run a maintenancewas

without any clothes in the drum.CLEANING THE DRAIN PUMPWARNING! Disconnect the mainsplug from the mains socket.Regularly check the drain pump filteran

180˚3. Turn the filter 180 degrees in anti-clockwise direc-tion to open it, without removing. Let the water flowout.4. When the bowl is full of water,

219. Put the filter back into the special guides by turningit clockwise. Make sure that you tighten the filter cor-rectly to prevent leakages.1210. Cl

EMERGENCY DRAINIf the appliance cannot drain the water, carry outthe same procedure, described in 'Cleaning thedrain pump' paragraph. If nec

POSSIBLE FAILURESProblem Possible solutionThe programme does notstart.• Make sure that the mains plug is connected to the mains socket.• Make sure tha

• Items that have been soiled with substances such as vegetableor mineral oil, acetone, alcohol, petrol, kerosene, spot removers,turpentine, waxes and

Problem Possible solutionThere is water on the floor.• Make sure that the couplings of the water hoses are tight and thereis not water leakages.• Make

After the check, activate the appliance. The programme continues from the point of interruption.If the problem occurs again, contact the Authorised Se

Programmes Load (kg)Energy con-sumption(kWh)Water con-sumption (litre)Approximate pro-gramme duration (mi-nutes)Cottons 40°C 8 0.89 80 185Synthetics 4

43

WWW.ZANUSSI.COM/SHOP157019971-A-462018

• The floor area on which the appliance is to beinstalled must be flat, stable, heat resistant andclean.• Keep the transit bolts in a safe place. If t

INSTALLATIONWARNING! Refer to Safety chapters.BE PREPARED FOR INSTALLATIONIt is recommended that installation iscarried out by two persons.THE APPLIAN

123. Remove the polystyrene protection from thebottom.124. Return the appliance in vertical position andremove the socket polystyrene protection.5. Re

FG7. Close the holes with the plastic caps you findin the user manual bag. Put the smallest cap Fin upper hole and the two bigger caps G in low-er hol

HOSE AND CABLE CONNECTION1100 mm 1450 mm760 mm1020 mm900 mm1360 mmmax 1000 mmmin. 600 mmmax 1000 mmmin. 600 mmThe inlet hose1. Remove the inl