Zanussi DE6744 User Manual download pdf (Page 5)

Before using your dishwasher for the first time:

1. Ensure that the electrical and water connections comply

with the installation instructions

2. Remove all packaging from inside the appliance

3. Set the water softener

4. Pour 1 litre of water inside the salt container and then fill

with salt

5. Fill the rinse aid dispenser

Setting the water softener

The dishwasher is equipped with a water softener designed to

remove minerals and salts from the water supply, which would

have a detrimental or adverse effect on the operation of the

appliance.

The higher the content of these salts, the harder your water is.

Water hardness is measured in equivalent scales, German

degrees, French degrees and PPM (parts per Million).

The softener should be adjusted according to the hardness of

the water in your area. Your local Water Authority can advise

you on the hardness of the water in your area.

The water softener must be set in both ways: manually, using

the water hardness switch and electronically, using the function

push buttons on the control panel.

If your water is level 1 it is already soft and therefore there

is no need to use salt.

Setting manually

1. Open the dishwasher door.

2. Remove the lower basket from the dishwasher.

3. Turn the water hardness switch to position 1 or 2 (see

table).

4. Replace the lower basket.

The dishwasher is factory set at position 2.

Setting electronically

The dishwasher is factory set at level 3. If it’s necessary to set

a new level, proceed as follows.

1. With the dishwasher switched off press function push

buttons 1 and 2 simultaneously .

2. While keeping the push buttons 1 and 2 pressed switch on

the dishwasher by pressing the On/Off push button.

The On/Off indicator light comes on.

At the same time, the indicator lights of push buttons 1 and

2 start flashing.

3. Press push button 1, the indicator light of push button 2

turns off, while the indicator light of push button 1 remains

fixed for about 5 seconds, after this it starts flashing

indicating the current level of the water softener.

The current level is indicated by the number of flashes

made by the indicator light of push button 1, that alternates

5 seconds off with a number of flashes, this for about 60

seconds.

Example:

1 flash = level 1

2 flashes = level 2

3 flashes = level 3

4 flashes = level 4

5 flashes = level 5

4. To change the level, press push button 1. Each time the

push button is pressed the level changes.

Example:

if the current level is 3, by pressing push button 1 once,

level 4 is selected.

if the current level is 5, by pressing push button 1 once,

level 1 is selected.

The indicator light of push button 1 remains off for about 5

seconds after which it starts flashing indicating the new

level selected.

5. To memorise the new level, switch off the dishwasher by

pressing the On/Off push button.

Prior to using for the first time

SO557

SO558

AA07

PPM

parts per million

°TH

french degrees

°dH

german degrees

manually

electronically

41 - 50

30 - 40

19 - 29

4 - 18

< 4

71 - 90

51 - 70

31 - 50

8 - 30

< 8

701 - 900

501 - 700

301 - 500

80 - 300

< 80

level 5

level 4

level 3

level 2

level 1

yes

Water hardness

Adjusting the water hardness

setting

Number of

flashes

Use of

salt

1 2 3 4 5 6 7 8 9 10 ... 19 20

Comments to this Manuals

No comments

Zanussi DE6744 User Manual Page 5

Comments to this Manuals

Related products and manuals for Dishwashers Zanussi DE6744