ENUser manualWasher-dryerZKN 7124
Programme - Maximum and Minimum Temperature - Cycle De-scription - Maximum Spin Speed - Maximum Fabrics Load -Type of LaundryOptionsDetergent Compart-
Degree of Drying Type of Fabric Drying Load Spin SpeedSuggested dry-ing time in Mi-nutesSECO PLANCHASuitable for ironingCotton and linen(sheets, table
• liquid detergents, preferably for low temperature washprogrammes (60°C max) for all types of fabric, or spe-cial for woollens only.The detergent and
• type of laundry• weight of the load size .The average drying time for a timed drying are indicated inthe «Drying programmes» chapter. The experience
Measure out the detergent and the fabric softenerPull out the dispenser drawer until it stops. Measureout the amount of detergent required, pour it in
Important! • The selected delay can be changed only after selectingthe washing programme again.• The door will be locked throughout the delay time. If
2. Select a spin cycle at the maximum spin speed al-lowed for the type of laundry in order to obtain thebest drying performances.3. Select the drying
Caution! Do not use a dosing device/ball whencarrying out a washing and drying programme.1. Load the laundry and add detergent and fabric soft-ener.2.
Remove the drawer bypressing the catch down-wards and by pulling itout. Flush it out under atap, to remove any tracesof accumulated powder.To aid clea
Remove fluff and objects from the pump.Make sure that the impeller of the pump can turn. If thisdoes not occur, contact the service centre.21Clean the
ContentsSafety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4Control panel _ _ _ _ _ _ _ _
Frost precautionsIf the machine is installed in a place where the tempera-ture could drop below 0°C, remove the remaining waterfrom the inlet hose and
Problem Possible cause/SolutionThe washing machine does not start:The door has not been closed. • Close the door firmly.The plug is not properly inser
Problem Possible cause/SolutionThere is water on the floor:Too much detergent or unsuitable detergent (creates too much foam) has beenused.• Reduce th
Problem Possible cause/SolutionSpinning starts late or the machinedoes not spin:The electronic unbalance detection device has cut in because the laund
Technical dataDimensions WidthHeightDepth60 cm85 cm63 cmElectrical connectionVoltage - Overall power - FuseInformation on the electrical connection is
After removing all thepackaging, carefully laymachine on it's back to re-move the polystyrene basefrom the bottom.Remove the power supplycable an
35°45°The other end of the inlet hose which connects to theappliance can be turned as showed in the picture.Do not place the inlet hose downwards. Ang
Environment concernsThe symbol on the product or on its packagingindicates that this product may not be treated ashousehold waste. Instead it should
www.zanussi.com/shop 132945671-A-502011
• After having installed the appliance, check that it is notstanding on the inlet and drain hose and the worktop isnot pressing the electrical supply
Product description1Detergent dispenser drawer2Control panel3Door opening handle4Rating plate5Drain pump6Adjustable feet123456Detergent dispenser draw
Control panelOn the following page there is a picture of the control panel. It shows the programme selector dial as well as thebuttons, pilot lights a
The pilot light corresponding to the selected dryness de-gree will illuminate.TIEMPO DE SECADOIf you wish to carry out a timed drying programme, press
• Delayed startThe Selected delay set by pressing the relevant button appears on the display for a few seconds, thenthe duration of the selected pro
Programme - Maximum and Minimum Temperature - Cycle De-scription - Maximum Spin Speed - Maximum Fabrics Load -Type of LaundryOptionsDetergent Compart-
Programme - Maximum and Minimum Temperature - Cycle De-scription - Maximum Spin Speed - Maximum Fabrics Load -Type of LaundryOptionsDetergent Compart-
Comments to this Manuals