Zanussi ZWN7100L User Manual

ENUser manualWashing MachineZWN 7100 LZWN 7120 L

•Pull out the dis-penser drawer untilit stops.The flap is down and you wish to usepowder detergent:• Turn the flap up.• Measure out thedetergent.•Pour

Select the spin speed by pressing button2When selecting a programme, the applianceproposes automatically the maximum spinspeed provided for that progr

sition. Start the new programme by pressingbutton 7 again.The washing water in the tub will be not emp-tied out.Interrupting a programmePress the butt

Button up pillowcases, close zip fasteners,hooks and poppers. Tie any belts or longtapes.Remove persistent stains before washing.Rub particularly soil

the water in your area can be obtained from therelevant water supply company, or from yourlocal authority. If the water hardness degree ismedium or hi

ProgrammeMaximum and Minimum Temperature - Cycle De-scription - Maximum Spin Speed - Maximum Fab-rics Load - Type of LaundryOptionsDetergent Com-partm

ProgrammeMaximum and Minimum Temperature - Cycle De-scription - Maximum Spin Speed - Maximum Fab-rics Load - Type of LaundryOptionsDetergent Com-partm

DescalingThe water we use normally contains lime. It is agood idea to periodically use a water softeningpowder in the machine. Do this separately from

Remove foreign bod-ies and fluff from thefilter seat and fromthe pump impeller.Check carefully whether the pump impellerrotates (it rotates jerkily).

Frost precautionIf the machine is exposed to temperatures be-low 0°C, certain precautions should be taken.• Turn off the water tap.• Unscrew the inlet

ContentsSafety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3Product description _ _ _ _ _ _ _ _ _ _ _ _

Problem Possible cause/SolutionThe machine does not start:The door has not been closed. • Close the door firmly.The plug is not properly inserted in t

Problem Possible cause/SolutionThere is water on the floor:Too much detergent or unsuitable detergent (creates too much foam)has been used.• Reduce th

Problem Possible cause/SolutionThe machine makes an un-usual noise:The machine is fitted with a type of motor which makes an unusualnoise compared wit

Programmes Load(kg)Energy con-sumption(kWh)Water con-sumption (li-tre)Approxi-mate pro-grammeduration(minutes)Remainingmoisture(%)1)ZWN7100LRemainingm

Open the porthole,remove the polystyr-ene block fitted onthe door seal and pullout all items from thedrum.Fill the smaller upperhole and the twolarge

Caution! The inlet hose must not belengthened. If it is too short and you donot wish to move the tap, you will have topurchase a new, longer hose spec

26 www.zanussi.com

27www.zanussi.com

www.zanussi.com/shop 192986484-A-052014

• Obey the maximum load volume of 8 kg (refer to the “Programmechart” chapter).• If the supply cord is damaged, it must be replaced by the manu-factur

• The appliance is to be connected to the wa-ter mains using the new supplied hose-sets.Old hose sets must not be reused.• Before you connect the appl

Product description1Detergent dispenser drawer2Control panel3Door opening handle4Rating plate5Drain pump6Adjustable feet123456Detergent dispenser draw

Child safetyMake sure that children or pets do not climbinto the drum. To prevent children and pets be-coming trapped inside the drum this machineinco

Rinse Hold Easy IronOptions Extra RinseSuper Quick Start/PauseEconomy Door lockedChild lock Delay StartProgramme selector dial, spin speed button and

• light blinking: the door is opening in a fewminutes.Display (10)10.1 10.2The display shows the following information:10.1: Child safety lockThis dev

1. Before pressing button 7: it will be impos-sible to start the machine.2. After pressing button 7: it will be impossi-ble to change any other progra