Zanussi ZWT71401WA User Manual

ENUser manualWasher-dryerZWT 71401 WA

4. If you wish to select a timed drying, press button 5until the time you want appears on the display (seethe «Drying Programme» table). Every time yo

Temperatures95° or 90°for normally soiled white cottonsand linen (e.g. tea cloths, towels, ta-blecloths, sheets...)60°/50°for normally soiled, colour

Tar stains: first treat with stain remover, methylated spiritsor benzine, then rub with detergent paste.Detergents and additivesGood washing results a

If using liquid detergents, a programme without prewashmust be selected.Your appliance incorporates a re-circulation system whichallows an optimal use

ProgrammeMaximum and Minimum TemperatureCycle DescriptionMaximum Spin SpeedMaximum Fabrics LoadType of LaundryOptionsDetergentCompartment9–12 — SYNTHE

ProgrammeMaximum and Minimum TemperatureCycle DescriptionMaximum Spin SpeedMaximum Fabrics LoadType of LaundryOptionsDetergentCompartment21 — SYNTHETI

Drying ProgrammesDegree of Drying Type of Fabric Max Load Spin SpeedSuggested dry-ing time inMinsIdeal for towelling materialsCotton and linen (bath-r

Cleaning the drawer recessHaving removed the draw-er, use a small brush toclean the recess, ensuringthat all washing powderresidue is removed fromthe

• Turn off the water tap.• Unscrew the hose fromthe tap.• Clean the filter in thehose with a stiff brush.• Screw the hose back onto the tap. Make sure

• : door open.Once the problem has been eliminated, press the button 8to restart the programme. If after all checks, the problempersists, contact your

ContentsSafety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4Control panel _ _ _ _ _ _ _ _

Problem Possible cause/SolutionThere is water on the floor:Too much detergent or unsuitable detergent (creates too much foam) has beenused.• Reduce th

Problem Possible cause/SolutionSpinning starts late or the machinedoes not spin:The electronic unbalance detection device has cut in because the laund

Electrical connectionVoltage - Overall power - FuseInformation on the electrical connection is given on the rating plate, on theinner edge of the appl

2. Remove the power supply cable, the draining hoseand inlet hose (if mounted) from the hose holders onthe rear of the appliance.3. Unscrew and remove

6. Fill the smaller upper hole and the two large oneswith the corresponding plastic plug caps supplied inthe bag containing the instruction booklet.Po

Important! Before connecting up the machine to newpipework or to pipework that has not been used for sometime, run off a reasonable amount of water to

A600 mm596 mm555 mm170 mm75 mm416 mm100 mm60 mmmin.820 mmmin.560 mm176,5 mm818 mmPreparation and assembly of the doorThe machine is originally prearra

D46If the door has to be opened from left to right, invert theposition of the plates (7), the magnet (4) and the plate (5)(Fig. B and E). Mount the co

• Measure out detergent according to the water hard-ness, the degree of soiling and the quantity of laundrybeing washed.28 www.zanussi.com

29www.zanussi.com

• After having installed the appliance, check that it is notstanding on the inlet and drain hose and the worktop isnot pressing the electrical supply

30 www.zanussi.com

31www.zanussi.com

www.zanussi.com/shop 132928350-A-502011

door, rotate the button anticlockwise until the groove isvertical.Product descriptionYour new appliance meets all modern requirements for effective tr

Detergent dispenser drawer Compartment for detergent used for prewash andsoak phase or for stain remover used during the stain ac-tion phase (if avail

Rinse holdBy selecting this function the water of the last rinse is notemptied out to prevent the fabrics from creasing. Beforeopening the door it wil

The Selected delay set by pressing the relevant buttonappears on the display for few seconds, then the dura-tion of the selected programme is displaye

if the selected programme/option it requires (see more de-tails in «Detergent dispenser drawer»).If required, pour fabric softener into the compartmen

Important! The selected delay can be changed only afterselecting the washing programme again.The Delay Start can not be selected with DRAINprogramme.S