Zanussi ZWGB7160P User Manual Page 1

ENUser manualWashing MachineZWGB 7160 P

If your drain hoselooks like this (seebeside) you do not re-quire the “U” piece”.Just push the hosefirmly in to the stand-pipe.• Directly to a built-i

SHOWERWASHINGMACHINEDISHWASHERBATHSINKTOILETBIDETRAINWATER‘RUN-OFF’SURFACE WATERDRAINS & SEWERSUNTREATEDDISCHARGERIVER RIVERTREATED DISCHARGEFOUL

By pressing these 2 buttons again, the acous-tic signal is reactivated.Child safety lockThis device permits you to leave the applianceunattended so yo

Tar stains: first treat with stain remover, methy-lated spirits or benzine, then rub with detergentpaste.Open the door by carefully pulling thedoor ha

Open the detergent dispenser drawer Compartment forpowder or liquid de-tergent used for mainwash. Compart-ment for liquid addi-tives (fabric softener

Warning! Do not use the flap in "DOWN"position with:• Gelatinous detergent or thick detergent.• Powder detergent.• With programmes with prew

2 3 45 69107 811Programme selector di-alSpecialsCottonsCottons+PrewashSyntheticsMix 20°DelicatesRinseDrainSpin5 ShirtsMini 30’JeansEasy IronCottons Wo

3Spin reduction By selecting a programme, the appliance proposes automati-cally the maximum spin speed provided for that programme.Press this button r

7Display7.17.27.3The display shows the following information:7.1Delay Start icon7.2Child safety lockThis device permits you to leave the appliance una

8DelayStartThe programme can be delayed from 30 min - 60 min - 90 min,2 hours and then by 1 hour up to a maximum of 20 hours bymeans of this button.Be

ContentsSafety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3Frost precaution _ _ _ _ _ _ _ _ _ _ _ _

9Start /PauseStart the programme by pressing the button 9• To start the selected programme, press the button 9, thecorresponding green pilot light sto

Warning! If there are children or pets inthe house, activate the child safety de-vice in the inner side of the door frame (formore details read "

Programme - Maximum and Minimum Temperature -Cycle Description - Maximum Spin Speed - MaximumFabrics Load - Type of LaundryOptionsDetergentCompartment

Programme - Maximum and Minimum Temperature -Cycle Description - Maximum Spin Speed - MaximumFabrics Load - Type of LaundryOptionsDetergentCompartment

Programmes Load(kg)Energy con-sumption(kWh)Water con-sumption (litre)Approximateprogramme du-ration (mi-nutes)Remainingmoisture(%)1)Cottons 60 °C 6 1.

• Use a stiff brush to clean and remove allwashing powder residue.• Clean all the removed parts of the dispens-er drawer under a tap to remove any tra

The filter is inserted correctly when theindicator on its top is visible andblocked.• close the filter cov-er;• insert the mainsplug again.Cleaning th

Fault code and malfunc-tionPossible cause / SolutionProblem with the watersupplyThe water tap is closed.• Open the water tap.The inlet hose is squashe

Malfunction Possible cause / SolutionThe appliance does notstart:The plug is not properly inserted in the power socket.• Insert the plug into the powe

Malfunction Possible cause / SolutionSpinning starts late orthe appliance does notspin:The electronic unbalance detection device has cut in because th

• Obey the maximum load volume of 6 kg (refer to the “Programmechart” chapter).• If the supply cord is damaged, it must be replaced by the manu-factur

30 www.zanussi.com

31www.zanussi.com

www.zanussi.com/shop 192977690-A-142013

• Before you connect the appliance to newpipes or pipes not used for a long time, letthe water flow until it is clean.• The first time you use the app

Environment concernsRecycle the materials with the symbol . Putthe packaging in applicable containers torecycle it.Help protect the environment and

1 Detergent dispenser drawer2 Worktop3 Control panel4 Door opening handle5 Rating plate (on the inner edge)6 Front adjustable feet7 Water drain hose8

Warning! Remove and keep all trans-it devices so that they can be refitted ifthe appliance ever has to be transportedagain.Necessary tools10 mm30 mm•

• Unscrew the three bolts and remove thehose holders.• Slide out the relevant plastic spacers.Warning! Donot remove thedrain hose fromthe rear support

Water inletConnect the hose toa tap with a 3/4”thread.35°45°Loosen the ring nut to angle the hose to theleft or right depending on the position of you