Zanussi ZDT 6255 Instruction Manual download pdf (Page 6)

Before using your dishwasher for the first time:

1. Ensure that the electrical and water connections comply

with the installation instructions

2. Remove all packaging from inside the appliance

3. Set the water softener

4. Pour 1 litre of water inside the salt container and then fill

with dishwasher salt

5. Fill the rinse aid dispenser

The water softener

The dishwasher is equipped with a water softener designed to

remove minerals and salts from the water supply, which would

have a detrimental or adverse effect on the operation of the

appliance.

The higher the content of these minerals and salts, the harder

your water is.

Water hardness is measured in equivalent scales, Clarke

degrees, French degrees (°TH) and mmol/l (millimol per litre -

international unit for the hardness of water).

The softener should be adjusted according to the hardness of

the water in your area. Your local Water Authority can advise

you on the hardness of the water in your area.

The water softener must be set in both ways: manually, using

the water hardness dial and electronically, using the function

push buttons on the control panel.

a)Setting manually

1. Open the dishwasher door.

2. Remove the lower basket from the dishwasher.

3. Turn the water hardness dial to position 1 or 2 (see table).

4. Replace the lower basket.

The dishwasher is factory set

at position 2.

b)Setting electronically

(The dishwasher must be switched off)

The dishwasher is factory set at level 5.

1. Press the On/Off button. All programme selection buttons

indicator lights will illuminate (setting mode).

If only one programme selection button indicator light is

illuminated, this means that a washing programme has

been selected.

The programme must be cancelled: press simultaneously

the function buttons 2 and 3 for about 2 seconds, the

indicator light of the set programme button starts flashing

for about 2 seconds.

After about 2 seconds the indicator lights of all the

programme selection buttons will illuminate indicating that

the set programme has been cancelled and that the

machine is now in setting mode.

2. Press simultaneously function buttons 2 and 3, until the

indicator lights of the function buttons 1, 2 and 3 start

flashing.

3. Press the function button 1, the indicator lights of function

buttons 2 and 3 turn off while the indicator light of the button

1 goes on flashing, at the same time the END OF CYCLE

indicator light illuminates, along with a sequence of audible

signals.

The current level is indicated by the number of flashes of

the END OF CYCLE indicator light and of audible signals

heard.

Example:

5 flashes + 5 audible signals = level 5.

4. To change the level, press function button 1. Each time the

button is pressed the level changes. (For the selection of

the new level see the chart).

Examples:

if the current level is 5, by pressing function button 1 once,

level 6 is selected.

if the current level is 10, by pressing function button 1 once,

level 1 is selected.

5. To memorise the operation, switch off the dishwasher by

pressing the On/Off button or wait about 60 seconds after

which the dishwasher will automatically return to setting

mode.

Prior to using for the first time

Clarke °TH mmol/l Range

manually

electronically

64 - 88

53 - 63

46 - 52

36 - 45

28 - 35

23 - 27

18 - 22

13 - 17

5 - 12

< 5

9,0 - 12,5

7,6 - 8,9

6,5 - 7,5

5,1 - 6,4

4,0 - 5,0

3,3 - 3,9

2,6 - 3,2

1,9 - 2,5

0,7 - 1,8

< 0,7

III

I/II

91 - 125

76 - 90

65 - 75

51 - 64

40 - 50

33 - 39

26 - 32

19 - 25

7 - 18

< 7

level 10

level 9

level 8

level 7

level 6

level 5

level 4

level 3

level 2

level 1

yes

Water hardness

Adjusting the water

hardness setting

Use

of salt

Number of flashes of the

"END OF CYCLE"

indicator light and of

audible signals

1 2 3 4 5 6 7 8 9 10 11 ... 23 24

Comments to this Manuals

No comments

Zanussi ZDT 6255 Instruction Manual Page 6

Comments to this Manuals

Related products and manuals for Dishwashers Zanussi ZDT 6255