Zanussi ZDT 6244 Instruction Booklet download pdf (Page 20)

Any electrical and/or plumbing work required to install

this appliance should be carried out by a qualified

electrician and/or plumber or competent person.

Remove all packaging before positioning the machine.

If possible, position the machine next to a water tap and a

drain.

Building-in

This dishwasher is designed to be fitted under a kitchen

counter or worksurface.

Attention!

Carefully follow the instructions on the enclosed template for

building in the dishwasher and fitting the furniture panel.

No further openings for the venting of the dishwasher are

required, but only to let the water fill and drain hose and power

supply cable pass through.

The dishwasher incorporates adjustable feet to allow the

adjustment of the height.

During all operations that involve accessibility to internal

components the dishwasher has to be unplugged.

When inserting the machine, ensure that the water inlet hose,

the drain hose and the supply cable are not kinked or

squashed.

Levelling

Good levelling is essential for correct closure and sealing of

the door.

When the appliance is correctly levelled, the door will not

catch on either side of the cabinet.

If the door does not close correctly, loosen or tighten the

adjustable feet until the machine is perfectly level.

Fixing to the adjacent units

The dishwasher must be secured against tilting.

Therefore make sure that the counter it is fixed under, is

suitably secured to a fixed structure (adjacent kitchen units

cabinets, wall).

Water supply connections

This dishwasher must be plumbed into a cold water supply.

For making the connection itself, the coupling nut fitted to the

machine’s supply hose is designed to screw onto either a 3/4"

inch gas thread spout or to a purpose made quick-coupling tap

such as the Press-block.

The water pressure must be within the limits given in the

"Technical specifications". Your local Water Authority will

advise you on the average mains pressure in your area.

The water inlet hose must not be kinked, crushed, or entangled

when it is being connected up.

The dishwasher features fill and drain hoses which can be

turned either to the left or the right to suit the installation by

means of the locknut. The locknut must be correctly fitted

to avoid water leaks. (Attention! NOT all models of

dishwashers have fill and drain hoses provided with locknut. In

this case, this kind of facility is not possible).

If the machine is connected to new pipes or pipes which have

not been used for a long time, you should run the water for a

few minutes before connecting the inlet hose.

Do not use, for connection, old hoses which have been

used in another appliance.

The dishwasher is fitted with safety devices that prevent the

wash water returning into the drinking water system and

comply with the applicable plumbing regulations.

Water outlet hose connection

The end of the drain hose can be connected in the following

ways:

1. To the sink outlet spigot, securing it to the underside of the

work surface. This will prevent waste water from the sink

running into the machine.

2. Hooked over the edge of the sink using the special curved

plastic guide (if provided with the machine).

3. To a stand pipe provided with vent-hole, minimum internal

diameter 4 cm.

The waste connection must be at a height of between 30 cm

(minimum) and 100 cm (maximum) from the bottom of the

dishwasher.

The drain hose can face either to the right or left of the

dishwasher

Ensure the hose is not bent or squashed as this could prevent

or slow down the discharge of water.

The sink plug must not be in place when the machine is

draining as this could cause the water to siphon back into the

machine.

If you use a drain hose extension it must be no longer than 2

metres and its internal diameter must be no smaller than the

diameter of the hose provided.

Likewise the internal diameter of the couplings used for

connections to the waste outlet must be no smaller than the

diameter of the hose provided.

Attention!

Our appliances are supplied with a security device to protect

against the return of dirty water back into the machine.

If the spigot of your sink has a "no return valve" incorporated

this can prevent the correct draining of your dishwasher.

We advise you therefore to remove it.

Installation instructions

CS18

1 2 ... 15 16 17 18 19 20 21 22 23 24 25

Comments to this Manuals

No comments

Zanussi ZDT 6244 Instruction Booklet Page 20

Comments to this Manuals

Related products and manuals for Dishwashers Zanussi ZDT 6244